How To Light An Rv Water Heater

Download Article

With an RV water heater, you lot can enjoy warm water even when camping ground in the wilderness. Even better, RV water heaters are easy to outset and operate, so you'll have hot water in no time!

i
Claw a hose to the RV'due south h2o intake valve. On the outside of your RV, find the intake valve. It usually has a blueish handle. Screw a hose onto the spigot and make certain it's tight and then the water doesn't leak out.^[1]
- Use a clean hose to bring fresh h2o into your RV, otherwise y'all could contaminate the water.
- If you have a tankless water heater, then merely connect a hose to the intake and a water source. Y'all don't have to make full a tank.^[2]
- Your RV may have particular instructions on filling the tank, then always cheque with the transmission first.
ii
Attach the other end of the hose to a water source. This could be the spigot for your garden hose if you're filling the tank at home, or a pump for filling upwards at campsites. Either way, connect the other end of the hose to this source and make sure it's tight to prevent whatsoever leaks.^[iii]
- If you're at a campsite, there are usually designated water sources for people to fill their campers. Ask where this is if y'all can't find information technology.
- Unless you accept a pump mechanism, you won't be able to fill your tank from a lake or stream. The h2o needs to be nether force per unit area to flow into the tank.
Advertizing
3
Turn the water source on. Open the valve by turning it counterclockwise. Water should start flowing into the tank.^[iv]
- On some RVs, y'all have to open the intake valve besides. If water isn't flowing into the tank, this might be the trouble.
4
Fill the water tank upwardly to the fill up line. Continue the water on and let the tank fill upwardly. When it reaches capacity, plough the water off and remove the hose from the intake and source socket.^[5]
- Some RVs accept a fill up meter near the intake valve. Otherwise, await at the tank itself to encounter when the water reaches the make full line.
- Continue in mind that h2o is heavy, and your vehicle volition utilise a lot of gas if information technology's at the max weight. You might want to make full the tank but halfway if you're planning on driving, so fill it the balance of the way at your destination.
5

Close the h2o heater bypass valve. The bypass valve directs the water away from the heater tank and brings it through your cold h2o tap. Shut the bypass valve so water flows into the h2o heater instead.^[6]
6
Plow on the hot water tap on 1 of your sinks. This brings water through the h2o heater and out of the faucet. If h2o is flowing, then the organisation is working correctly.^[7]
- If water isn't coming out of the tap, then it means the hot tank doesn't have water in it. Double check to brand certain the bypass valve is closed.
7
Let the water flow until there is no more air coming out. The water might sputter a little bit when yous kickoff turn information technology on. This is normal, every bit information technology just means air is haemorrhage out from the system. Keep running the faucet until the water comes out smoothly without whatsoever air, then you can start the water heater.^[viii]
- Never light the water heater if there is still air in the system. This could impairment the tank.

1
Open your propane tank. The tank should be on the exterior of your RV. Plough the knob counterclockwise to open it and permit propane flow.^[ix]
- Don't open the propane tank until only earlier you're gear up to light the water heater. Information technology's dangerous to leave propane running if you're non using information technology.
two
Flip the "H2o Heater" switch inside your RV if you have an auto start. Electronic auto starters are very piece of cake to apply. Simply hitting the "Water Heater" switch to ignite the pilot light and start heating the water.^[10]
- There is usually an indicator lite next to this switch indicating whether or not the heater is lit.
- If your heater won't ignite, and so the propane tank might not exist open up. Otherwise, you may accept a problem with your switch. Take the RV in for servicing.
3
Open the control panel on the outside of your RV for manual starts. Manual light h2o heaters require a few more steps. The panel is usually held down by a latch or screws. Open it up to access the pilot lite and ignition controls.^[11]
- Always read and follow the directions for opening your RVs control panel.
4
Turn the knob on the control console to "Pilot" for a manual start. The control knob turns so yous can select the setting y'all want. Rotate it then it says "Pilot" so you can ignite the pilot light.^[12]
- Propane won't offset flowing until you press the knob downwards. Don't printing until you lot're gear up to ignite the pilot light.
5
Ignite the pilot lite with a long charcoal-broil lighter. Press the control knob down to release propane. Then slide the lighter right upward to the pilot light and ignite information technology to lite the gas.^[thirteen]
- Keep the knob pressed down for a few seconds to warm upwards the system.
- This is only for manual starts. An automatic starter volition ignite the pilot light with no further steps.
6
Switch the command knob from "Airplane pilot" to "On." In one case the pilot calorie-free is lit, then light the principal heater. Rotate the control knob to the "On" position. This ignites the chief heater and starts heating the h2o in the tank.^[14]
- Keep your face up away from the control panel when you low-cal the heater. There may exist a quick flash when it ignites.
- It takes about 30 minutes for the h2o in the tank to heat up after you light the heater.^[15]
- When you're finished using the water heater, turn the propane off. It's dangerous to exit it running when you aren't using it.

1
Connect the RV to a power source. Run your RVs power cable to a ability source and plug information technology in. About campsites accept electric hookups like this for RVs.^[sixteen]
- If you're at a army camp, at that place might be an extra charge for using the electricity.
2
Turn the water heater power switch on. The water heater power switch is usually inside the motel and looks like a normal light switch. Flip it to the On position to start heating the water.^[17]
- The switch is ordinarily labeled "Water Heater," and then it should be piece of cake to detect.
- For older models, the On switch might exist on the water heater itself rather than inside the motel.
three
Look 60-90 minutes for the water to heat up. Electric heaters have a flake longer than propane heaters to warm the water. Depending on the size of the tank, it'll have about 60-90 minutes, so be patient before using the hot water.^[18]
- RV h2o heaters unremarkably have a light to indicate when they're on. If the light doesn't plow on, the bulb might be burned out or the water heater may not be working. Take the RV to a repair shop for servicing.
4
Turn the switch off when you lot're washed using the hot water. Once the h2o is hot, conserve electricity past flipping the h2o heater switch off. Go out the heater off until yous're set to use it once again.^[19]
- If you're notwithstanding using electricity in your RV, like for lights or the stove, then get out the power source plugged in. Otherwise, you can unplug it when the h2o is hot.

Ask a Question

200 characters left

Include your email address to go a message when this question is answered.

Submit

Advertizement

Ever read and follow the instructions that come with your RV h2o heater. Different models may work differently.
Some RVs accept both propane and electric heaters, so you tin choose which to use.
It's best to have your RV serviced before going on a trip. If anything goes wrong, you probably won't be able to fix information technology yourself.

Advert

RV water heaters are tough to make repairs on unless y'all're a professional, and so it'south always best to bring it to a repair shop if something isn't working right.^[20]

Advertizing